GamePP Frequently Asked Questions

When taking a corner at 300 km/h, I'd get these tiny micro-freezes that made me obsessed with trying to overpower them via overclocking. The Gainward RTX 5070 Ti Storm OC has a high factory clock, but under extreme loads, I noticed 0.05V momentary voltage drops, causing the core clock to jump wildly between 2.5GHz and 2.1GHz. I first tried 'Maximum Performance' in the driver, but the core temp spiked to 85℃ and triggered thermal throttling—totally missed the mark. I then used MSI Afterburner to manually add a +25mV voltage offset and set a custom fan curve to hit 80% speed at 70℃. In RTSS, the frame time variance shrank from 12-30ms to a tight 8-12ms, and the fluidity was night and day. I did have some random reboots after the first voltage bump, but dropping the core clock by 15MHz made it rock solid. Core temps now sit between 68℃ - 74℃. Comparing the curves, the stability is finally where it needs to be. Last updated onMarch 29, 2026 9:18 PM.

The combat in this game is an absolute blast, and when the loading is fast, the immersion is just peak. However, once the Zhitai TiPro9000 1TB's SLC dynamic cache fills up, write speeds crash from 7000MB/s to under 1000MB/s, causing 15-25ms of loading lag. I tried switching the power plan to 'Balanced', but that just tanked my read speeds to 4000MB/s—obviously a bad move for a high-performance SSD. Instead, I went into Device Manager, bumped the NVMe queue depth from 1024 to 2048, and forced the write cache flush policy. CrystalDiskMark showed random 4K reads jumping from 50MB/s to 70-80MB/s. I had a brief moment where the drive wasn't detected after the tweak, but switching to 'High Performance' power mode killed that bug. Temps are stable at 45-58℃ with the heatsink. Storage analysis confirms the speeds are back, and the cache mode is finally switched. Last updated onMarch 23, 2026 1:19 PM.

That feeling of absolute fluidity finally came back once I locked down the scheduling. The ASUS Z890-A was dumping heavy physics calculations onto the E-cores, causing frame times to jump wildly between 15-40ms. I tried turning on 'Game Mode' in Windows, but it was a band-aid fix; the stutters still happened during the most intense firefights. I went into the BIOS, forced the scheduling to 'Performance First,' and switched the Windows power plan to 'Ultimate Performance.' RivaTuner showed frame times instantly tightening to 8-12ms. I did run into a snag where the CPU temp jumped 6℃ because the voltage was too aggressive, so I had to apply a slight negative offset to balance it out. Now the CPU sits at 68-76℃ with fans at 1600 RPM. The scheduling bugs are gone, and the game feels snappy. Last updated onMarch 23, 2026 9:54 PM.

When pushing the tropical jungle foliage at 4K, my CPU temp blew past the 90℃ limit, which actually made me excited to try some extreme tuning. The Jonsbo CR-1400E ARGB is a small cooler, and it hits thermal saturation fast under the Remastered load, leaving my core clocks hovering around 3.0GHz. I first tried capping the CPU state to 99% in Windows, which dropped temps by 10℃ but tanked my 1% lows from 45 to 30 FPS—completely unacceptable. I went into the BIOS, flipped the fan mode from Silent to Performance, maxed the ceiling at 2200 RPM, and swapped to a high-conductivity metal paste. RTSS showed core temps drop from 94℃ to 78-84℃, and the frame rate stabilized between 55-65 FPS. At first, the fan noise was like having a hairdryer in my ear, but I managed it by tweaking the curve below 60℃. CPU power draw stayed around 120-140W, with fans steady at 1400-1600 RPM. Last updated onApril 7, 2026 9:48 AM.

When a monster jumps out of the shadows, you want that load to be instant for the full thrill. However, once the Zhitai TiPro9000 4TB's dynamic SLC cache fills, the write speed craters from 7000MB/s to under 1000MB/s, causing 15-25ms resource delays. I tried the 'Balanced' power plan, but that just tanked my read speeds from 7000MB/s to 4000MB/s—totally useless for a high-end SSD. I went into Device Manager, bumped the NVMe controller queue depth from 1024 to 2048, and enabled the forced write cache flush policy. CrystalDiskMark showed 4K random reads jumping from 50MB/s to 70-80MB/s. I had a brief moment where the drive wasn't detected after the change, but switching to 'High Performance' power mode solved it. Drive temps sat between 45-58℃ with the heatsink. Storage analysis tools confirm the speed is back, and it's holding steady at 45-58℃. Last updated onMarch 8, 2026 9:27 AM.