Question 1

Is a fan curve tweak necessary for the DeepCool AK500 when Control 2 drops frames during debris scenes?

Accepted Answer

When the screen gets filled with flying debris, my FPS would dive from 80 down to 30, which is a wild ride but incredibly frustrating. The AK500's default fan profile just can't handle sustained loads like this, with temps hitting 88°C - 92°C and triggering heavy clock fluctuations. I tried 'Power Saver' mode in BIOS, but while it saved 4°C, the physics simulations slowed down to a crawl—totally unacceptable. I went into the motherboard control center, set the fans to hit 100% at 65°C, and swapped to a high-performance thermal paste. AIDA64 confirmed peak temps dropped from 92°C to 68°C - 74°C, and the frame drops vanished. I did have an issue where the fans kept ramping up and down rapidly between 60°C - 65°C, so I added a 5-degree hysteresis window to stop the noise. Fans now sit at 1500 RPM, and frame times are rock steady at 5.1ms - 6.4ms.

Question 2

Is thread priority the issue when my Onda 9D4-DVH stutters in crowded GTA V RP city fights?

Accepted Answer

Joining an RP server with a hundred players is a blast, but the sudden frame drops were absolutely killing the vibe. The default scheduling on the Onda 9D4-DVH was struggling with concurrent network requests and physics, with response times swinging wildly between 20-40ms, causing the main game thread to jump between cores constantly. I tried enabling 'Game Mode' in Windows, but that did nothing but hide some notifications—totally useless. I eventually used a process Lasso-style tool to force the game onto the performance cores and locked the minimum processor state to 100% in the power plan. In Task Manager, the core load stopped jumping around and flattened out, and the stutters vanished. The only downside was that my background apps lagged for a second until I assigned them to the efficiency cores. CPU temps are stable at 68-74℃ with fans at 1500-1700 RPM. Profiling tools show the scheduling latency is gone, and memory stays at 58-63℃.

Question 3

God of War Ragnarok combat is stuttering because the Fanxiang S910PRO 2TB is throttling; should I change the cooling?

Accepted Answer

Right when a massive boss charges at the screen, my frames would plummet from 110 to 40, which is a total mood killer. The Fanxiang S910PRO 2TB has insane PCIe 5.0 speeds, but it runs hot—hitting 82-88℃ under load, which triggers the thermal throttle and halves the bandwidth. I tried a BIOS power-saving tweak, but while it dropped the temp by 5 degrees, the load times became unbearable. I ended up replacing the stock thermal pads with high-performance ones and disabled PCIe Link State Power Management. HWInfo showed the peak temp drop from 85℃ to 62-68℃, and the frame drops vanished. I actually had a bit of a struggle with the first pad installation—it wasn't sitting flat, and temps actually went up by 2 degrees until I tightened the screws properly. Now, sequential reads are locked at 10000MB/s. The read/write mode switch is finally confirmed in the performance panel, but this drive requires a beefy cooler to stay stable.

Question 4

Should I optimize virtual memory if my Vastarmor RX 9070 XT Super Alloy Pro has scheduling lag in Valorant?

Accepted Answer

Hitting a clean headshot is an amazing rush, but having the game stutter immediately after just kills the mood. The VRAM controller on the Vastarmor Radeon RX 9070 XT Super Alloy Pro was struggling with high-frequency small file reads, with response times swinging between 15-30ms. I tried enabling Windows Game Mode, but that did absolutely nothing except clean up the UI—a total waste of effort. I ended up manually setting the virtual memory to a fixed range of 32GB-64GB and locked the VRAM frequency at 2400MHz. In Task Manager, the VRAM peak stabilized at 6.5-7.2GB, and the overflow-induced stutters stopped. My boot time actually slowed down by about 5 seconds after fixing the page file, but I fixed that by cleaning up my startup apps. Temps are steady at 62-68℃ with fans at 1300-1500 RPM. The internal profiler shows the scheduling lag is gone.

Question 5

I'm seeing frequency swings and frame drops during combat in Dune Awakening with Asgard Thor DDR5. Help!

Accepted Answer

Right in the middle of a sandstorm fight, my FPS would suddenly tank from 80 down to 40, which is an absolute rollercoaster of frustration. It turns out the default profiles for the Asgard Thor DDR5 6400 have some compatibility quirks with certain boards, causing the memory controller to jump wildly between 5600MHz - 6400MHz. I tried lowering the in-game settings, but while the FPS went up, the game looked terrible, and that was a compromise I wasn't willing to make. I went into the BIOS, locked the frequency at a steady 6000MHz, and bumped the voltage from 1.35V to 1.38V for absolute stability. Monitoring with RTSS, the frame times tightened from 18-38ms to a smooth 12-16ms, and the drops disappeared. Interestingly, locking it at 6000MHz actually cost me about 2 FPS at first, until I fine-tuned the secondary timings to get the performance back. Memory temps stayed stable between 52-58℃. I verified the frequency lock in the driver panel, and temps held at 52-58℃.

Question 6

I'm getting memory checksum errors and stutters during loading in Like a Dragon: Ishin on my Soyo SY-Classic B660M. SoC voltage fix?

Accepted Answer

Seeing Kyoto in detail is amazing, but the random crashes were a total buzzkill. The Soyo SY-Classic B660M memory controller struggles with high-frequency DDR5, with SoC voltage swinging wildly between 1.1V and 1.2V, causing checksum errors during large page allocations. I tried enabling Windows Game Mode, but that did absolutely nothing. I went into the BIOS, locked the SoC voltage at 1.25V, and tightened the timings from 36-36-36-76 to 32-38-38-72. In AIDA64, read speeds jumped from 48GB/s to 54-58GB/s with zero errors over three hours. My boot time slowed down by about 10 seconds initially, but disabling the memory training option fixed that. RAM temps are 52-58℃ and CPU is 68-74℃. Benchmarks show the system is finally stable, with fans steady at 1400-1600 RPM.

Question 7

Granblue Fantasy: Relink drops from 60 to 30 FPS during combat on Kingbank 8GB 3600. Fix?

Accepted Answer

Whenever I unleash a screen-clearing skill, the frame rate just tanks from 60 to 30, which is a total buzzkill in the middle of a fight. The default XMP profile on the Kingbank Yin Jue 8GB 3600MHz was fighting with my motherboard, causing the memory controller to bounce between 3200-3600MHz. I tried lowering the in-game settings, but the game looked like mud and the drops stayed, which was unacceptable. I went into the BIOS, locked the frequency at 3200MHz, and bumped the voltage from 1.35V to 1.38V for absolute stability. RTSS showed frame times tightening from 16-35ms to 11-15ms. Interestingly, I actually lost 2 FPS after locking 3200MHz until I manually tuned the secondary timings. RAM temps are steady at 45-51℃. The mode switch is finally confirmed.

Question 8

I'm getting weird frame drops in Nioh 2 combat on my B760M-D PRO V20, is it a CPU issue?

Accepted Answer

Landing a perfect guard feels amazing, but that feeling is instantly killed when a micro-stutter hits right at the peak of the action. The default scheduling on the Colorful B760M-D PRO V20 was messing up the task split between P-cores and E-cores, causing a 5-10ms delay as the main game thread bounced between cores. I tried the standard 'Game Mode' fix in Windows, but it did nothing—just a total waste of time. I eventually used a process affinity tool to force the game onto the P-Cores and locked the minimum processor state to 100% in the power plan. In Task Manager, the core load went from erratic spikes to a smooth distribution, and the stutters vanished. The only downside was that my background apps felt a bit sluggish for a second, which I fixed by assigning them specifically to the E-Cores. CPU temps are now stable at 65-71℃ with fans at 1400-1600 RPM. Profiling tools show the scheduling latency is gone, with frame times locked at 5.1-6.4ms.

Question 9

Zenless Zone Zero takes forever to get past the initial self-test, should I optimize BIOS?

Accepted Answer

After clicking the launch icon, I was staring at a black screen for ten full seconds before the logo even appeared. In a fast-paced action game, that kind of delay is just frustrating. The default boot strategy on the ASRock H310CM-ITX/ac was scanning every single USB device, adding a massive 8-12 second lag to the initialization. I tried swapping in a faster SSD, but that only shaved off about a second—a total band-aid solution. I finally went into the BIOS, disabled the redundant network boot options in the Fast Boot menu, and locked the boot order to just the system drive. My boot timer showed the POST time drop from 15 seconds to a crisp 4-6 seconds. I did accidentally lock myself out of the OS after disabling network boot due to a config error, but I fixed it by recalibrating the CSM mode. Board idle temps are steady at 32-38℃. The system panel confirms the boot mode switch worked, and temps are still 32-38℃.

Question 10

The Last of Us Part 1 keeps stuttering during scene loads on my Manli RTX 5060. Is this a VRAM issue?

Accepted Answer

Seeing those wasteland vistas is amazing, but the VRAM overflow stutters totally killed the vibe. The 8GB on the Manli RTX 5060 is barely enough for 4K textures, forcing the system to swap to slow system RAM, which caused massive 20-40ms spikes. I tried the usual Windows Game Mode trick, but it did nothing—just a placebo. I dove into the NVIDIA Control Panel, set the shader cache to 10GB, and manually locked the virtual memory to a fixed 32GB-64GB range. In Task Manager, the VRAM peak stayed around 7.2-7.8GB, and those instant freezes stopped. I noticed the system took about 5 seconds longer to boot after the page file change, but cleaning up my startup apps fixed that. Temps are chilling at 65-71℃ with fans at 1400-1600 RPM. The internal profiler shows the VRAM pressure is gone, and frame times are finally sitting at 5.1-6.4ms.

GamePP Frequently Asked Questions

I'm getting signal jitter and frame drops in Remnant 2 during heavy combat with Crucial DDR5 4800. Do I need to tune timings?

I'm seeing micro-stutters in MGSV Definitive Edition on my Galax B760M D4, should I change RAM frequency?

I'm seeing slow load times in Manor Lords on my Fanxiang S910Max. This is taking forever!

Why does Unknown 9 look so blurry with DLSS enabled on my Soyo SY-A320D4+ system?

A Plague Tale: Requiem keeps crashing during heavy rendering on my ASUS B760M. Why is it failing?