GamePP Frequently Asked Questions

I can finally face the final boss without my PC melting, though this AIO is getting old. I managed to squeeze every bit of performance out of it, which was a huge relief. The B240 was showing a 10-15℃ thermal drift under load, with cores idling in the 88-94℃ range, causing my FPS to swing wildly between 60 and 45. I tried forcing the pump to full speed via software, but the high-pitched whine was so piercing I couldn't hear the game—completely unacceptable. I ended up stripping the block, applying high-conductivity thermal paste, and switching to an aggressive fan curve based on CPU package temp in the BIOS. HWiNFO showed the load temps plummet from 92℃ to 76-80℃, and the FPS fluctuations totally stopped. The fans were a bit too loud at idle initially, but dropping the low-load RPM to 600 RPM made it perfect. Now it stays between 65-72℃. Benchmarks confirm the cooling mode switch worked, though I suspect the pump is nearing the end of its life. Last updated on2026-04-07 12:41:23。

Fighting waves of Tyranids is great until the screen starts hitching, which totally ruins the immersion. The Jonsbo CR-1400 is a compact cooler, and it just can't move heat fast enough during high-power bursts, leading to heat buildup at the base and temps swinging between 85-92℃. This triggered some light throttling. I tried 'Ultimate Performance' mode in Windows, but it only gave me 2 extra FPS—a total waste of time since the bottleneck is clearly physical. I went into the BIOS, pushed the fan ceiling to 100%, and slapped two high-static pressure fans in the front of the case to force more cold air in. RTSS showed my frame times tightening from 18-35ms down to 14-17ms. I had a bit of a resonance vibration after adding the fans, but some rubber dampeners killed the noise. Now the CPU sits comfortably at 78-83℃. Stress tests prove the thermal parameters are verified, though this cooler is definitely pushed to its absolute limit. Last updated on2026-04-08 21:15:58。

Late-game turn processing in this game is basically a torture test for your CPU; every time I hit 'End Turn', the fans spool up like a Boeing 747, it's insane. Because of the fan ramp-up delay, the RT620P lets the CPU jump from 60℃ to 96℃ in a single second, creating this jarring 'system freeze' feeling. I tried capping the max processor state to 99% in Windows, but the turn calculations became painfully slow—a total nightmare of a compromise. I went back into the BIOS, slashed the fan response time from 0.3s to 0.1s, and applied a -0.05V voltage offset to curb the heat at the source. My temp logger showed the peaks dropped from 96℃ to a manageable 85-88℃, and that stuttering feeling vanished. The fans were oscillating like crazy at first with the faster response, so I widened the temp window by 2℃ to stop the hunting. Now the CPU stays between 70-78℃. I've exported all the stress test logs and the thermal performance is finally where it should be. Last updated on2026-04-06 17:48:39。

About two hours into the game, the smoothness just vanished and the frame drops became blatant. The DeepCool AK620 was suffering from total thermal saturation during sustained high-power loads, with core temps creeping from 75℃ up to a stifling 92-95℃, which tanked my clocks from 4.8GHz down to 3.2GHz. I tried lowering the graphics settings to reduce the load, but the game looked like mud and it didn't actually fix the heat—just a desperate, useless move. I eventually dove into the BIOS and adjusted the fan offset, bumping the RPM by 15% in the 60-80℃ window, and swapped my rear exhaust for a higher static pressure fan. Running AIDA64 stress tests, the temps stabilized at 81-84℃ even after an hour, ending the cliff-dive throttling. I did deal with some weird turbulence noise at first, but tilting the front fans slightly solved the airflow clash. Now the fans hold steady at 1400-1600 RPM. Three hours of gameplay later and the performance is flat, no more dipping. Last updated on2026-04-06 14:10:17。

Whenever I hit the crowded streets of Bohemia, my CPU temps shot from 62℃ up to a scary 94-98℃, which instantly triggered the motherboard's thermal throttling. The default fan curve on the Thermalright PA120 SE is way too lazy before 80℃, letting heat soak into the fins until the frame times spiked from 16ms to a choppy 45ms. I tried just blasting the fans at 100% in the BIOS, but while it dropped temps by 5℃, the noise was like a jet engine in my room—completely unbearable. I eventually went into the motherboard control panel and redefined the PWM curve, setting a stepped 4-8% increase specifically between 75-85℃, while also cranking up the front case intake. Monitoring via HWiNFO showed the core temps finally capped at 82-86℃, with clock speeds stabilizing within a +/- 100MHz range. I did notice some annoying fan RPM hunting at first, but adding a 0.7s hysteresis timer smoothed it right out. Now the fans sit steady at 1200-1500 RPM. After a few stress tests, the thermal profile is rock solid and the settings are saved. Last updated on2026-03-11 22:24:56。