Question 1

Can optimizing pump speed stop BioShock 4 from hanging when the Valkyrie V360 can't keep up?

Accepted Answer

The optimization in this game is a complete joke; it just hammers the CPU. My V360 felt like it was trying to cool a space heater. Core temps were dancing around 98°C, and the system would trigger a protection mechanism that froze the screen for two seconds—a total nightmare. I tried limiting the processor state to 99% in Windows Power Options, which dropped temps by 5°C but turned the game into a slideshow. Absolute garbage solution. I switched the pump from 'Smart' to 'Full Speed' and locked the radiator fans to the motherboard's maximum voltage mode. HWiNFO showed temps plummet from 99°C to 78°C - 84°C, and the freezes finally stopped. I had a weird issue with air bubbles making a gurgling noise at first, which I only fixed by moving the radiator to the top of the case. The fans now scream at 2000 RPM, sounding like a helicopter taking off. I exported the logs to confirm the fan speeds are now stable at 1400 - 1600 RPM.

Question 2

My Biostar H310MHD3 has terrible random reads causing drops in Genshin, will virtual memory help?

Accepted Answer

Using this H310 board for modern games feels like trying to run a marathon in flip-flops. In the Sumeru rainforest, my frame rate was bouncing between 30 and 60 FPS, which is just pathetic. The memory bandwidth on the Biostar H310MHD3 gets saturated instantly with 4K textures, leaving the CPU idling for 15-30ms. I tried dropping the settings to Low, but the game looked like mud and the stutters stayed—a complete waste of time. I ended up manually setting the virtual memory to a fixed 16GB-32GB range on my fastest NVMe partition and disabled the Windows Indexing service. In RTSS, the frame time graph went from looking like a heart attack to a steady 18-22ms, and map transitions are actually usable now. My boot time took a hit of about 8 seconds initially until I cleaned up the boot entries. Board temps are 45-52℃ with power draw around 30-40W. I exported the latency logs to verify the fix, and fans are humming steadily at 1400-1600RPM.

Question 3

Mass Effect planet hops are lagging because the Intel 760P 512GB cache is full; can I fix this with priority settings?

Accepted Answer

Watching that loading circle spin forever was honestly testing my sanity. Once the SLC cache on the Intel 760P 512GB gets filled with temp files, the write speed collapses from 3000MB/s to around 800MB/s—it's a complete joke. I started by cleaning out system temp folders, but that only saved me 0.2 seconds, which felt like a slap in the face. I finally installed the latest vendor NVMe drivers, killed unnecessary indexing services in Windows Disk Management, and switched the write cache policy to forced flushing. CrystalDiskMark showed random 4K reads improving from 42-50MB/s to 58-65MB/s. I did run into a problem where searching for files became sluggish after disabling indexing, so I had to manually re-index my core folders. Temps are okay, between 42-50℃. I exported all the latency logs via a performance analyzer, and frame times are now stable at 5.1-6.4ms, though the drive still feels dated for 2026 titles.

Question 4

Can adjusting the power limit fix the frame drops caused by power fluctuations on a Gainward RTX 5080 in Apex Legends?

Accepted Answer

This 5080 is an absolute power hog at 4K Ultra. In the final circles, my FPS was bouncing between 120 and 180, which was honestly pathetic. The default power wall on the Gainward RTX 5080 Storm OC is way too conservative, causing the core to throttle slightly under heavy load, leading to 12-25ms frame time jitter. I tried lowering settings to High, but the game looked blurry and the drops were still there—a complete waste of time. I used a tool to bump the power limit to 115% and locked the core clock at 2650MHz. In RTSS, the frame time graph went from looking like an EKG to a flat line at 8-12ms. The card hit 84℃ after 20 minutes of this, so I had to switch the fan curve to a linear growth mode to keep it under control. Now it stays between 76-82℃ and pulls 320-360W. I exported all the frame data to verify, and the power parameters are finally dialed in.

Question 5

I'm getting memory overflow and stuttering in complex scenes in Kai no Kiseki with Corsair DDR5. Why?

Accepted Answer

I can't believe this game is actually maxing out 32GB of RAM; it felt like my PC was trying to breathe through a straw. Loading a large map would push memory usage above 95%, turning the game into a slideshow, which is just ridiculous. I tried closing every single background app, but it only saved about 1GB, which felt like a waste of time. I finally went into the Advanced System Settings and manually set the virtual memory to a fixed block of 32768MB - 49152MB on my NVMe drive. In Resource Monitor, the commit charge dropped from 45GB to a more manageable 32-38GB, and the stuttering frequency plummeted. I did notice a slight delay during system boot after the first change, but I fixed that by disabling a bunch of useless startup items. Memory temps were hovering around 50-56℃, which is barely acceptable. I used a performance analyzer to export the memory curves for archiving, with fans screaming at 1400-1600 RPM. It's playable now, but the memory management in this game is a mess.

Question 6

I'm getting huge memory controller latency spikes in Tales of Arise on my Jginyue B760M Gaming D5. Can priority settings fix this?

Accepted Answer

The memory scheduling on this board is like watching a snail race. In the open areas of Tales of Arise, my FPS was bouncing between 40 and 80, which is just pathetic. The Jginyue B760M Gaming D5 in Gear 2 mode was hitting 110-120ns of latency—a total waste of hardware. I tried lowering the graphics to Medium, but the game just looked blurry and the stutters remained. I eventually forced Gear 1 in the BIOS and bumped the DRAM voltage to 1.35V to keep it from crashing. Monitoring with RTSS, the frame time graph went from looking like an EKG to a flat line at 14-18ms. I did hit two Blue Screens of Death during launch, but loosening the tRFC to 500 finally stabilized it. RAM temps are 55-61℃ and CPU is 65-71℃. Exported logs confirm frame times are now rock steady at 14-18ms.

Question 7

Banishers: Ghosts of New Eden is stuttering like crazy on 8GB HyperX Savage. Any fix?

Accepted Answer

Trying to run this game on 8GB of RAM is a total joke; it feels like my PC is breathing through a straw. Just loading a scene pushes usage to 98%, and the game turns into a slideshow. I tried closing every background app, but that only saved about 200MB—basically useless. I went into Advanced System Settings and manually locked the virtual memory to a fixed range of 16384-24576MB on my fastest NVMe drive. Resource Monitor showed the commit charge drop from 15GB to around 11-13GB, and the stutters finally calmed down. I did hit some boot delays after the change until I stripped my startup apps. RAM temps are sitting at 40-46℃. It's not a perfect fix, but I managed to export the performance curves and the game actually runs now.

Question 8

FFXV is lagging in cities on my MSI B450M MORTAR MAX, is the motherboard failing?

Accepted Answer

This old board is barely hanging on with modern optimized titles. In Insomnia, my framerate was jumping between 40 and 70 FPS, which was just pathetic. The VRM on the MSI B450M MORTAR MAX was hitting 95℃ under load, forcing the CPU to throttle and creating a 15-30ms frame time jitter. I tried lowering the graphics to Medium, but the game just looked blurry and the lag stayed—a complete waste of effort. I ended up rigging a small fan to blow directly onto the VRM heatsinks and manually locked the CPU power limit to 105W in the BIOS. Looking at RTSS, the frame time graph went from looking like an EKG to a flat line between 18-22ms. It was a huge jump in smoothness. Interestingly, my 1% lows actually dropped by 2 frames after locking the power, but bumping my RAM to 3200MHz sorted that out. VRM temps now stay between 75-81℃ and the CPU is at 68-74℃. I exported the voltage logs to verify, and the fans are steady at 1400-1600 RPM.

Question 9

Delta Force triggers VRM throttling during firefights, can I fix this with process priority?

Accepted Answer

The cooling on this tiny board is a complete joke. Running this at 4K felt like my VRMs were literally frying. My clock speeds would tank from 5.0GHz down to 3.2GHz, and the game turned into a slideshow—it was absolutely ridiculous. I tried running the whole rig open-air, and while it dropped 10 degrees, that's not exactly a viable way to play a game. I eventually went into the BIOS and capped the CPU PL1 power limit at 125W, then set the chassis fan curve to hit 100% the second it hit 60℃. HWInfo showed the VRM temps drop from a terrifying 108℃ to a manageable 82-88℃, and the stutters finally stopped. Interestingly, the first time I capped the power, my 1% lows actually dropped by 3 frames, so I had to tweak the memory voltage to compensate. The fans are now screaming at 2200 RPM, and the noise is pretty obnoxious. I exported the frequency logs to verify the stability, and the fans are now locked between 2200-2400RPM.

Question 10

I'm getting frame drops in God of War: Ragnarok due to power fluctuations. Can priority settings help?

Accepted Answer

This 5060 Ti felt like it was fighting for its life with 4K textures. In the massive scenes of Ragnarok, the frame rate was bouncing between 45 and 80 FPS, which is just pathetic. The default power limit on the Gigabyte RTX 5060 Ti 16G is way too conservative, causing the core to downclock under heavy load and creating 15-22ms of frame time jitter. I tried dropping the settings to Medium, but the game looked blurry and the stutters stayed—a complete waste of my time. I used MSI Afterburner to bump the power limit to 110% and locked the core clock at 2550MHz. The RTSS graph, which looked like a heart attack before, finally flattened out to 14-18ms. I did have a scare when temps hit 82℃ after 15 minutes, but a linear fan curve brought it under control. It now stabilizes at 74-79℃, pulling 180-210W. Fans are humming along at 1400-1600 RPM, and the data export confirms the power delivery is finally consistent.

GamePP Frequently Asked Questions

I get a long black screen and 100% disk usage on my WD SN850 2TB when starting the Mario emulator.

Ark 2 has terrible input lag during terrain loading on my Biostar B650MT. Is this a hardware flaw?

My Seagate FireCuda 530 gets way too hot during map loads in Overwatch 2, causing drops. Fix?

Phantom Blade Zero (Beta) keeps crashing with my Crucial 8GB DDR4 2400, can priority tweaks help?

My Gainward RTX 5070 Ti Snow Step OC 2.0 is throttling and dropping frames under high load in Sword and Fairy 7 (Upgrade). Can I fix this with process priority?