Question 1

I get sudden FPS drops while swinging in Spider-Man 2 with a WD SN850 2TB. Why is it lagging?

Accepted Answer

Every time I dive between Manhattan skyscrapers, the frame rate tanks from 60 FPS to a choppy 22 FPS, which is jarring as hell. The WD SN850 2TB's 4K random reads were fluctuating between 14-38ms when handling fragmented assets, causing the engine to hang while waiting for data. I tried running a disk defrag out of desperation, which I later realized is completely pointless for NVMe drives and just adds unnecessary wear—I felt like an idiot for that. I eventually used a partition tool to ensure a perfect 4K alignment and bumped the disk I/O priority to 'High' via the registry, while killing Windows Indexing. Monitoring with RTSS, the frame time spikes dropped from 48ms to a manageable 17-23ms. The only downside was that system file searches became sluggish until I added a specific exclusion for the game folder. The drive stays cool at 44-52℃. The input lag is gone, and the swinging finally feels responsive to my fingertips.

Question 2

RE Village keeps crashing to desktop on high settings with my G.Skill DDR5 6800, should I tweak virtual memory?

Accepted Answer

Every time I entered a large indoor area, the game would just vanish and dump me back to the desktop without any warning; the unpredictability was stressing me out. The insane 6800MHz clock on the G.Skill Trident Z Royal was putting massive pressure on the memory controller, leading to a 0.06V transient voltage drop and subsequent checksum errors. I first tried increasing the virtual memory size, but the crash frequency didn't budge—that kind of blind trial-and-error felt like a total dead end. I then went into the BIOS advanced menu, loosened the primary timings from 32-38-38-84 to 34-40-40-88, and locked the memory voltage at 1.42V. After 5 consecutive rounds of MemTest86, the error count dropped from 18 to zero, and my session time went from 20 minutes to 6 hours without a crash. I actually tried pushing the voltage to 1.45V at first, but the RAM hit 65℃ and triggered a thermal reboot until I backed it off to 1.42V. Now, memory temps are a steady 52-58℃ and VRM is at 60-65℃. Stress tests confirm it's rock steady.

Question 3

My Pacific Drive keeps freezing for seconds during complex scene transitions. Should I fix memory?

Accepted Answer

Every time I drove into a new zone, the game would just hang for about 3 seconds, which is absolutely soul-crushing when you're under pressure. With only 8GB of Crucial DDR4 2400, my memory usage was hitting 94-98%, forcing the system into a constant cycle of page swapping. I tried using some 'RAM cleaner' software, but that was a joke—the FPS would jump for a second and then the freezes would actually get worse. I eventually manually set my virtual memory to 24GB and forced it onto a dedicated partition on my NVMe SSD, while disabling three useless Windows telemetry services. In Resource Monitor, the commit charge expanded from 12GB to 20-26GB, and the freezes almost entirely disappeared. I initially left it on 'System Managed,' but the page file kept bouncing between my C and D drives, causing massive IO latency until I locked it down manually. Temps stayed chill at 40-45℃. The game is finally playable, and the controls feel snappy again.

Question 4

I'm getting weird input delays and micro-stutters during fast movement in Deathloop on my Biostar A320MH. How do I fix this?

Accepted Answer

Every time I hit the attack button, there's this tiny, perceptible hitch in the frame. In a fast-paced action game where timing is everything, this kind of input lag is an absolute nightmare and had me feeling seriously anxious. I ran LatencyMon and found the USB controller on the Biostar A320MH PRO was spiking DPC latency up to 2.9ms, which was causing the frame time to jump all over the place. My first instinct was to swap from a USB 3.0 to a 2.0 port; it lowered the latency slightly, but it capped my controller polling rate at 125Hz, which is a total dealbreaker for competitive play. I eventually went into Device Manager and disabled three redundant USB ports I wasn't using, then used a tool to manually reassign the IRQ interrupts for the NIC and GPU. After that, LatencyMon showed DPC latency pinned below 0.6ms, and that floaty input feeling completely vanished. I did have a scare where I accidentally messed up the audio driver config and lost all sound, but a quick service restart fixed it. Chipset temps are 40-48℃ and RAM is 36-40℃. Tested with an input lag tool and it's finally back to normal.

Question 5

I'm getting huge frame drops while galloping in Ghost of Tsushima on my H310M. Page file fix?

Accepted Answer

Every time I ride into a new zone, the frame rate plummets from 60 down to 20 FPS, which is just heartbreaking given how beautiful the game looks. The bus bandwidth on the aging Galax H310M Warrior D4 is struggling with modern 4K texture streams, with response times swinging between 15-40ms. I tried defragging the drive first, which I quickly realized was a total joke for an NVMe SSD and just added unnecessary wear—that whole process was honestly just stressful. I eventually set the virtual memory to a manual 32GB on a dedicated fast SSD partition and killed the Windows Indexing service. RTSS showed the frame time spikes dropping from 45ms to a manageable 18-22ms. The only downside was that system search became sluggish, but I fixed that by adding the game folder to the exclusion list. CPU temps are sitting at 68-75℃. The resource loading lag is way down, and the controls finally feel responsive to my fingertips.

Question 6

My Gainward RTX 2060 keeps lagging in Horizon Forbidden West jungle areas, is it overheating?

Accepted Answer

Every time I stepped into a dense forest, my FPS would tank from 50 down to 28, and the sudden chugging was honestly stressing me out. The Gainward RTX 2060 was hitting 88-92℃ under load, triggering a hardware thermal throttle that crushed my clock speed from 1695MHz down to about 1300MHz. I tried switching Windows to 'Ultimate Performance' mode, but while the fans spun faster, the temps stayed high—it felt like fighting a losing battle. I eventually tore the card down, swapped in some high-performance thermal pads, and aggressivey tweaked the fan curve in MSI Afterburner to hit 90% speed once it reaches 70-80℃. Checking HWInfo, the core finally stabilized at 72-78℃, and the drops stopped. I almost bent the PCB by over-tightening the heatsink screws, which was a close call. Now it runs at 70-76℃ with fans at 2200-2500 RPM. A one-hour stress test proves the clock curve is finally flat.

Question 7

I'm getting sudden FPS drops in Hellblade 2 on my B760M; should I mess with virtual memory or is it voltage?

Accepted Answer

Every time the game transitioned to a high-detail area, my FPS would tank from 60 to 30, which is jarring as hell on Ultra settings. Looking at HWiNFO, the default voltage strategy on the ASUS B760M Heavy Artillery was swinging between 11.7V and 12.3V during power spikes, causing micro-delays in the CPU cores. I tried the 'Ultimate Performance' power plan in Windows, but that just pushed my temps to a scary 96°C, triggering a thermal throttle that made the stuttering even worse—a total waste of time. I eventually dove into the BIOS, set the Load-Line Calibration (LLC) to 'Medium,' and applied a core voltage offset of -0.040V. RTSS showed frame times tightening from 16-42ms to a consistent 11-15ms, and the game finally felt fluid. I did run into a BSOD the first time I applied the voltage change, but nudging the compensation back to +0.020V stabilized the system. The VRM area now stays around 58-65°C. After a stress test, the voltage curve is smooth, and the input lag is practically gone.

Question 8

My Jonsbo CR-1400E ARGB can't handle Atomic Heart's load, causing system crashes. Fix it?

Accepted Answer

Every time I entered a complex industrial zone, the game would just vanish and dump me back to the desktop without any error message—it was incredibly frustrating. The Jonsbo CR-1400E ARGB just couldn't keep up with the transient power spikes, and my CPU temps were hitting 96-98℃, causing the core voltage to wobble by about 0.05V. I tried 'Power Saver' mode in Windows, but that tanked my FPS to 30, which is a joke. Instead, I dove into the BIOS and capped the CPU power limit (PL1/PL2) at 65W and moved the fan trigger point from 60℃ down to 40℃. Running AIDA64's FPU stress test, the rig actually survived three hours without a reboot, staying between 78-84℃. I almost bricked my board trying to flash a third-party microcode before this, and I had to use the CMOS jumper to bring it back to life. Now it sits at 75-82℃ with fans at 1800 RPM. Crashes are gone, but the lower power ceiling is a necessary evil.

Question 9

I'm getting instant stutters in Frostpunk 2 during population peaks with my Huntkey Blizzard T600. Should I mess with virtual memory?

Accepted Answer

Whenever I panned the camera across the crowded slum districts, the frame rate would plummet from 60 FPS to 25 FPS, which is jarring as hell. The Huntkey Blizzard T600 has a sluggish fan response time, lagging by 3-5 seconds during CPU temp spikes, letting the core hit 95°C before reacting. I first tried lowering the shadow quality, but while average FPS went up by 5, that gut-punching stutter remained—a band-aid solution that left me feeling anxious. I went into the BIOS, dropped the fan trigger temp to 60°C, and switched to a steep linear ramp-up curve. RTSS showed my 1% lows jump from 18 FPS to a much healthier 35-42 FPS. I did hit a snag where the max RPM caused a weird chassis resonance noise, which I only fixed after replacing the fan mounting clips. Now temps are stable at 74°C - 80°C, and the input response finally feels connected to my fingertips.

Question 10

The Division's intense combat is causing core scheduling issues on my i5 13490F, leading to instant stutters.

Accepted Answer

Every time I pop a skill with massive explosions, my frame rate tanks from 90 FPS down to 35 FPS instantly, which is honestly nerve-wracking. The i5 13490F was showing a 200ms response lag during load switching, with CPU usage bouncing violently between 60% and 95%. I tried ramping my fans to 100% via software, but it just made my PC sound like a jet engine for a measly 2℃ drop—totally frustrating. I went into the BIOS, swapped the power management from Balanced to High Performance, and set a manual core voltage offset of +0.015V. Checking HWInfo, the clocks finally stabilized between 4.5-4.8GHz, and the drops vanished. I actually overshot the voltage on my first try and triggered a thermal shutdown, so I had to dial it back by 0.01V to get it stable. Now the CPU sits at 72-80℃ and the VRMs are at 68-74℃. A ten-minute combat stress test confirms the frequency curve is finally flat.

GamePP Frequently Asked Questions

How to real-time monitor cooler Thermalright Peerless Assassin 120 SE ARGB temperature in GamePP during Valorant when high temp causes lag?

"How to view Corsair Vengeance DDR5-6000 RAM usage trends in Genshin Impact over the past week?"

"How to switch GamePP in-game monitoring panel to vertical mode while playing Fable?"

How to use real-time monitoring in GamePP to detect the usage of SSD ZhiTai Ti600 (1TB)?

CPU temperature stays very high while running Black Myth: Wukong, how to use GamePP's performance statistics to view historical temperature curves and analyze the issue?